Ngarkues i ulët

Fliegl ZTS 200 P

Additional information
Low loader semi-trailer chassis
Steel welded construction
Turntable with robust ball bearing, storage box recessed in the turntable extension
Foldable rear support
Chocks with holder
Aluminum side impact protection
Half-shell fenders on the 1st axle, quarter-shell fenders in front of and behind the 2nd axle
with anti-splash flaps behind each axle
1 plastic toolbox, with insert base, w=620/h=360/d=440 mm, can be locked with a padlock. (Lock not included)
Extensions can be pulled out to 3,000 mm (not in the rear slope)
(However, the track width of the construction machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm), storage compartment for wooden planks in the middle of the loading area, wooden planks 70 mm for extending to 3000 mm
Tie-down points, low loader
3 pairs of tie-down points, 10 tons each, integrated in the front of the floor
6 pairs of tie-down rings, 10 tons each, recessed on the top and side of the outer frame
1 x in the area near the kingpin, the remaining ones are distributed in between, with a maximum distance of 1200 mm,
1 x rear slope
5 pairs of ring tie-down points recessed in the outer frame, 5 tons each (instead of stringer pockets)
Coupling device, low loader turntable
Drawbar with tested 40 mm drawbar eye
Axles + Suspension
SAF drum brake axles
Axle/chassis laser-aligned to reduce tire wear and fuel consumption
Parabolic suspension with maintenance-free steel-rubber bearing
Wheels and tires
235 / 75 R 17.5
as chosen by the manufacturer
Steel rims in twin arrangement, factory silver
Braking system
2-line pneumatic braking system
Spring-loaded parking brake
2 non-interchangeable coupling heads at the front, with connection lines to the towing vehicle
ABS and ALB, with ABS plug at the front, with connection cable
Note: The trailer may only be pulled by towing vehicles that ensure the effectiveness of the ABS!
Electrical system
24 Volt, multi-chamber lights, yellow LED lighting on the sides
2 white/red position lights at the rear
2 white position lights at the front
1 rotating beacon with holder, switched via the parking lights (beacon can be removed)
2 pairs of warning panels, double LED-illuminated and extendable to 3,000 mm
2 x 7-pin non-interchangeable plugs at the front, with connection cable
Floor
Front area, steel floor
followed by 70 mm softwood floor, steel/diamond plate in the wheel arch area
Rear slope with 70 mm softwood floor
Low loader bed incl. rear slope 8,200 mm
Access ramps
Steel ramps 2,800 mm long, 750 mm wide, can be shifted sideways
additional ramp securing device, foldable at the bottom (to prevent the ramps from sliding sideways, not in conjunction with a side hydraulic ramp shifting system)
covered with wood
with spring-assisted support
Operating instructions
A special permit is required for a 10,000 kg axle load. The permit must be applied for separately in each federal state; the legislator does not have to guarantee approval for 20 tons of GVW. Customer's risk.
The stated total weight is technically possible; depending on the load, the total weight may not be reached while complying with the permissible axle/support and drawbar loads.
Approval / Signs
Approval country: Germany
Test approval according to EC 2007/46
24/7 service hotline
prepared for license plate holder, two lines
Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear
Warning sign according to ECE - 70
Painting
Frame, DB
Ksdpoi Ri N Hsfx Af Aslu

Njoftimi është përkthyer automatikisht. Mund të ketë gabime në përkthim.